home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Software Vault: The Gold Collection
/
Software Vault - The Gold Collection (American Databankers) (1993).ISO
/
cdr11
/
ibmlist.zip
/
PCERROR.LST
< prev
next >
Wrap
File List
|
1989-10-12
|
65KB
|
1,321 lines
TITLE: 1XX SYSTEM BOARD OR SETUP ERRORS...........................1001
101 SYSTEM BOARD Interrupt failure.
102 SYSTEM BOARD BIOS ROM Checksum Error (pc)
102 SYSTEM BOARD Timer failure. (pcat)
103 SYSTEM BOARD BIOS ROM Checksum Error (pc)
103 SYSTEM BOARD Timer interrupt failure. (pcat)
104 SYSTEM BOARD Protected mode failure. (pcat)
105 SYSTEM BOARD Last 8042 command not accepted.
106 SYSTEM BOARD Converting logic test.
107 SYSTEM BOARD Hot NMI test.
108 SYSTEM BOARD Timer bus test.
109 SYSTEM BOARD Direct memory access test error.
121 SYSTEM BOARD Unexpected hardware interrupts occurred.
131 SYSTEM BOARD Cassette wrap test failed.(bad system board)
151 SYSTEM BOARD Real Time Clock Failure (or CMOS ERROR on 5170)
152 SYSTEM BOARD CMOS Date and Time error (5170)
161 SYSTEM BOARD System Options Error (Battery failure) CMOS chip power
162 SYSTEM BOARD System options error (Run SETUP) CMOS Checksum error
163 SYSTEM BOARD Time and date not set (Run SETUP).
164 SYSTEM BOARD Memory size error (Run SETUP) CMOS does not match sys.
199 SYSTEM BOARD User indicated configuration not correct.
~~~~~
TITLE: 2XX MEMORY ERRORS..........................................1002
201 MEMORY (RAM) Memory test failed.
202 MEMORY (RAM) Memory address error (line error 00..15)
203 MEMORY (RAM) Memory address error (line error 16..23)
221 ERROR (this is not a PC error code it is a COINS error code)
~~~~~
TITLE: 3XX KEYBOARD ERRORS........................................1003
301 KEYBOARD Keyboard software reset failure or stuck key failure
302 KEYBOARD User indicated error or PCAT system unit keylock is locked.
303 KEYBOARD Keyboard or system unit error.
304 KEYBOARD Keyboard or system unit error; CMOS does not match system.
365 KEYBOARD Replace Keyboard
366 KEYBOARD Replace Interface Cable
367 KEYBOARD Replace Enhancement Card or Cable
~~~~~
TITLE: 4XX MONOCHROME/PRINTER ADAPTER ERRORS......................1004
401 MONOCHROME Monochrome memory test or horizontal sync frequency test
408 MONOCHROME User indicated display attributes failure.
416 MONOCHROME User indicated character set failure.
424 MONOCHROME User indicated 80X25 mode failure.
432 MONOCHROME Parallel port test failed (monochrome adapter).
~~~~~
TITLE: 5XX COLOR GRAPHICS ADAPTER ERRORS..........................1005
501 COLOR ADAPTER Color memory test failed, horizontal sync frequency test,
or video test failed.
508 COLOR ADAPTER User indicated display attribute failure.
516 COLOR ADAPTER User indicated character set failure.
524 COLOR ADAPTER User indicated 80X25 mode failure.
532 COLOR ADAPTER User indicated 40X25 mode failure.
540 COLOR ADAPTER User indicated 320X200 graphics mode failure.
548 COLOR ADAPTER User indicated 640X200 graphics mode failure.
556 COLOR ADAPTER Light pen test failed.
564 COLOR ADAPTER User indicated screen paging test failure.
~~~~~
TITLE: 6XX DISKETTE DRIVE AND ADAPTER ERRORS......................1006
601 DISKETTE Diskette power on diagnostics test failed.
602 DISKETTE Diskette test failed; boot record is not valid.
603 DISKETTE Diskette size failure
606 DISKETTE Diskette verify function failed.
607 DISKETTE Write protected diskette.
608 DISKETTE Bad command diskette status returned.
610 DISKETTE Diskette initialization failed.
611 DISKETTE Timeout diskette status returned.(could not read dskt)
612 DISKETTE Bad NEC diskette status returned.(BIOS dskt routines)
613 DISKETTE Bad DMA diskette status returned.(overrun failure)
614 DISKETTE DMA boundary software problem.
621 DISKETTE Bad seek.....Diskette status returned.
622 DISKETTE Bad CRC....diskette status returned.
622 * Reformat scratch diskette and retry test before
622 accepting the error code as correct.
623 DISKETTE Record not found....diskette status returned.
623 * Reformat scratch diskette and retry test before
623 accepting the error code as correct.
624 DISKETTE Bad address mark....diskette status returned.
624 * Reformat scratch diskette and retry test before
624 accepting the error code as correct.
625 DISKETTE Bad NEC seek.....diskette status returned.
626 DISKETTE Diskette data compare error.
626 * Reformat scratch diskette and retry test before
626 accepting the error code as correct.
627 DISKETTE Diskette line change error
628 DISKETTE Diskette removed
~~~~~
TITLE: 7XX MATH COPROCESSOR ERRORS................................1007
701 MATH COPROCESSOR failure replace Coprocessor
~~~~~
TITLE: 9XX PARALLEL PRINTER ADAPTER ERRORS........................1008
901 PARALLEL PRINTER ADAPTER Parallel printer adapter test failed.
914 PARALLEL PRINTER ADAPTER Conflict between 2 parallel printer adapters.
(ast printer port 1 and parallel printer card
etc.)
~~~~~
TITLE: 10XX PARALLEL PRINTER ADAPTER ERRORS.......................1009
1001 PARALLEL PRINTER ADAPTER Parallel printer adapter test failed.
1014 PARALLEL PRINTER ADAPTER Conflict between 2 parallel printer adapters.
(ast printer port 1 and parallel printer card
etc.)
~~~~~
TITLE: 11XX ASYNC ADAPTER ERRORS..................................1010
1101 ASYNC Asynchronous communications adapter test failed.
Make sure adapter not set for "current loop".
1110 ASYNC Modem Status Register not clear
1111 ASYNC Ring Indicate failure
1112 ASYNC Trailing Edge Ring indicate failure
1113 ASYNC Receive and Delta Receive line signal detect failure
1111 ASYNC Receive line signal detect failure
1115 ASYNC Delta Receive line signal detect failure
1116 ASYNC Line Control Register (all bits cannot be set)
1117 ASYNC Line Control Register (all bits cannot be reset)
1118 ASYNC Transmit holding and/or shift register stuck on
1119 ASYNC Data Ready stuck on
1120 ASYNC Interrupt Enable Register (all bits cannot be set)
1121 ASYNC Interrupt Enable Register (all bits cannot be reset)
1122 ASYNC Interrupt pending stuck on
1123 ASYNC Interrupt ID register stuck on
1124 ASYNC Modem Control Register (all bits cannot be set)
1125 ASYNC Modem Control Register (all bits cannot be reset)
1126 ASYNC Modem Status Register (all bits cannot be set)
1127 ASYNC Modem Status Register (all bits cannot be reset)
1128 ASYNC Interrupt ID Failure
1129 ASYNC Cannot force overrun error
1130 ASYNC No Modem Status Interrupt
1131 ASYNC Invalid Interrupt status pending
1132 ASYNC No data ready
1133 ASYNC No data available Interrupt
1134 ASYNC No Transmit Holding Interrupt
1135 ASYNC No Interrupts
1136 ASYNC No Receive Line Status Interrupt
1137 ASYNC No Receive data available
1138 ASYNC Transmit Holding Register not empty
1139 ASYNC No Modem Status Interrupt
1140 ASYNC Transmit Holding Register not empty
1141 ASYNC No Interrupts
1142 ASYNC NO IRQ4 Interrupt
1143 ASYNC No IRQ3 Interrupt
1144 ASYNC No Data Transferred
1145 ASYNC Max Baud rate failed
1146 ASYNC Min Baud rate failed
1148 ASYNC Timeout Error
1149 ASYNC Invalid Data Returned
1150 ASYNC Modem Status Register error
1151 ASYNC No DSR to Delta DSR
1152 ASYNC No Data Set Ready
1153 ASYNC No Delta
1154 ASYNC Modem Status Register not clear
1155 ASYNC No CTS and Delta CTS
1156 ASYNC No Clear to Send
1157 ASYNC No delta CTS
~~~~~
TITLE: 12XX ALTERNATE ASYNC ADAPTER ERRORS........................1011
1201 ALT ASYNC Asynchronous communications adapter test failed.
1210 ALT ASYNC Modem Status Register not clear
1211 ALT ASYNC Ring Indicate failure
1212 ALT ASYNC Trailing Edge Ring indicate failure
1213 ALT ASYNC Receive and Delta Receive line signal detect failure
1211 ALT ASYNC Receive line signal detect failure
1215 ALT ASYNC Delta Receive line signal detect failure
1216 ALT ASYNC Line Control Register (all bits cannot be set)
1217 ALT ASYNC Line Control Register (all bits cannot be reset)
1218 ALT ASYNC Transmit holding and/or shift register stuck on
1219 ALT ASYNC Data Ready stuck on
1220 ALT ASYNC Interrupt Enable Register (all bits cannot be set)
1221 ALT ASYNC Interrupt Enable Register (all bits cannot be reset)
1222 ALT ASYNC Interrupt pending stuck on
1223 ALT ASYNC Interrupt ID register stuck on
1224 ALT ASYNC Modem Control Register (all bits cannot be set)
1225 ALT ASYNC Modem Control Register (all bits cannot be reset)
1226 ALT ASYNC Modem Status Register (all bits cannot be set)
1227 ALT ASYNC Modem Status Register (all bits cannot be reset)
1228 ALT ASYNC Interrupt ID Failure
1229 ALT ASYNC Cannot force overrun error
1230 ALT ASYNC No Modem Status Interrupt
1231 ALT ASYNC Invalid Interrupt status pending
1232 ALT ASYNC No data ready
1233 ALT ASYNC No data available Interrupt
1234 ALT ASYNC No Transmit Holding Interrupt
1235 ALT ASYNC No Interrupts
1236 ALT ASYNC No Receive Line Status Interrupt
1237 ALT ASYNC No Receive data available
1238 ALT ASYNC Transmit Holding Register not empty
1239 ALT ASYNC No Modem Status Interrupt
1240 ALT ASYNC Transmit Holding Register not empty
1241 ALT ASYNC No Interrupts
1242 ALT ASYNC NO IRQ4 Interrupt
1243 ALT ASYNC No IRQ3 Interrupt
1244 ALT ASYNC No Data Transferred
1245 ALT ASYNC Max Baud rate failed
1246 ALT ASYNC Min Baud rate failed
1248 ALT ASYNC Timeout Error
1249 ALT ASYNC Invalid Data Returned
1250 ALT ASYNC Modem Status Register error
1251 ALT ASYNC No DSR to Delta DSR
1252 ALT ASYNC No Data Set Ready
1253 ALT ASYNC No Delta
1254 ALT ASYNC Modem Status Register not clear
1255 ALT ASYNC No CTS and Delta CTS
1256 ALT ASYNC No Clear to Send
1257 ALT ASYNC No delta CTS
~~~~~
TITLE: 13XX GAME CONTROLLER ERRORS................................1012
1301 GAME CONTROL Game control adapter test failed.
1302 GAME CONTROL Joystick test failed.
~~~~~
TITLE: 14XX GRAPHICS PRINTER ERRORS...............................1013
~~~~~
TITLE: 15XX SYNCHRONOUS DATA LINK CONTROL (SDLC) ADAPTER ERROR....1014
1501 SDLC ADAPTER Adapter test failed.
1510 SDLC ADAPTER 8255 port B failure.
1511 SDLC ADAPTER 8255 port A failure.
1512 SDLC ADAPTER 8255 port C failure.
1513 SDLC ADAPTER 8253 timer 1 did not reach terminal count.
1514 SDLC ADAPTER 8253 timer 1 stuck on.
1515 SDLC ADAPTER 8253 timer 0 did not reach terminal count.
1516 SDLC ADAPTER 8253 timer 0 stuck on.
1517 SDLC ADAPTER 8253 timer 2 did not reach terminal count.
1518 SDLC ADAPTER 8253 timer 2 stuck on.
1519 SDLC ADAPTER 8273 port B ERROR
1520 SDLC ADAPTER 8273 port A ERROR.
1521 SDLC ADAPTER 8273 command ADAPTER Read timeout.
1522 SDLC ADAPTER Interrupt level 4 failure.
1523 SDLC ADAPTER Ring Indicate stuck on.
1524 SDLC ADAPTER Receive clock stuck on.
1525 SDLC ADAPTER Transmit clock stuck on.
1526 SDLC ADAPTER Test indicate stuck on.
1527 SDLC ADAPTER Ring indicate not on.
1528 SDLC ADAPTER Receive clock not on.
1529 SDLC ADAPTER Transmit clock not on.
1530 SDLC ADAPTER Test indicate not on.
1531 SDLC ADAPTER data set ready not on.
1532 SDLC ADAPTER Carrier detect not on.
1533 SDLC ADAPTER Clear to send not on.
1534 SDLC ADAPTER Data set ready stuck on.
1536 SDLC ADAPTER Clear to send stuck on.
1537 SDLC ADAPTER Level 3 interrupt failure.
1538 SDLC ADAPTER Receive interrupt results error.
1539 SDLC ADAPTER Wrap data miscompare.
1540 SDLC ADAPTER DMA channel 1 error.
1541 SDLC ADAPTER DMA channel 1 error.
1542 SDLC ADAPTER Error in 8273 error checking or status reporting.
1547 SDLC ADAPTER Stray interrupt level 4.
1548 SDLC ADAPTER Stray interrupt level 3.
1549 SDLC ADAPTER Interrupt presentation sequence timeout.
~~~~~
TITLE: 16XX DISPLAY SATION EMULATION ERRORS.......................1015
1604 DSEA ADAPTER error, or twinaxial problem
1608 DSEA Adapter error, or twinaxial problem
1624 DSEA Adapter error.
1634 DSEA Adapter error.
1644 DSEA Adapter error.
1652 DSEA Adapter error.
1654 DSEA Adapter error.
1658 DSEA Adapter error.
1664 DSEA Adapter error.
1662 DSEA Interupt Level switches set incorrectly or DSEA Adapter error.
1668 DSEA Interupt Level switches set incorrectly or DSEA Adapter error.
1674 DSEA Station address error or DSEA Adapter error.
1684 DSEA Feature not installed or Device address switches set incorrectly.
1688 DSEA Feature not installed or Device address switches set incorrectly.
~~~~~
TITLE: 17XX FIXED DISK DRIVE AND ADAPTER ERRORS...................1016
1701 FIXED DISK PC Fixed disk POST error (drive not ready)
1701 FIXED DISK PCAT Hardfile adapter test failed
1702 FIXED DISK PC Fixed disk adapter error.
1702 FIXED DISK PCAT Timeout error
1703 FIXED DISK PC Fixed disk drive error.
1703 FIXED DISK PCAT Seek Failure
1704 FIXED DISK PC Fixed disk adapter or drive error.
1704 FIXED DISK PCAT Controller Failure
1705 FIXED DISK No Record Found
1706 FIXED DISK Write Fault Error
1707 FIXED DISK Track "0" Error
1708 FIXED DISK Head Select Error
1709 FIXED DISK Bad ECC.
1710 FIXED DISK Read Buffer Overrun
1711 FIXED DISK Bad Address Mark
1712 FIXED DISK Bad Address Mark
Make sure Adv. Diags. were loaded from cold boot (5170 only)
1713 FIXED DISK Data Compare Error
1714 FIXED DISK Drive Not Ready
1730 FIXED DISK Replace Adapter
1731 FIXED DISK Replace Adapter
1732 FIXED DISK Replace Adapter
1780 FIXED DISK Fixed disk 0 failure (fatal no IPL Capability)
1781 FIXED DISK Fixed disk 1 failure (fatal drive "0" may still be O.K.)
1782 FIXED DISK Fixed disk controller failure (fatal no IPL from hardfile)
1790 FIXED DISK Fixed disk 0 error (non fatal...f1 can attempt IPL from
1790 drive) check carefully for improper cabling...
1791 FIXED DISK Fixed disk 1 error (non fatal...f1 can attempt IPL from
1791 drive)
~~~~~
TITLE: 18XX EXPANSION UNIT ERRORS.................................1017
1801 EXPANSION I/O expansion unit POST error.
1810 EXPANSION Enable/Disable failure.
1811 EXPANSION Extender card warp test failed (disabled).
1812 EXPANSION High order address lines failure (disabled).
1813 EXPANSION Wait state failure (disabled).
If 3278/79 adapter or /370 adapter installed check for
down level Extender Adapter (ECA011).
1814 EXPANSION Enable/Disable could not be set on.
1815 EXPANSION Wait state failure (disabled).
1816 EXPANSION Extender card warp test failed (enabled).
1817 EXPANSION High order address lines failure (enabled).
1818 EXPANSION Disable not functioning.
1819 EXPANSION Wait request switch not set correctly.
1820 EXPANSION Receiver card wrap test failure.
1821 EXPANSION Receiver high order address lines failure.
~~~~~
TITLE: 20XX BINARY SYNCHRONOUS COMMUNICATIONS ADAPTER ERRORS......1018
2001 BSC POST failed.
2010 BSC 8255 port A failure.
2011 BSC 8255 port B failure.
2012 BSC 8255 port C failure.
2013 BSC 8253 timer 1 did not reach terminal count.
2014 BSC 8253 timer 1 stuck on.
2016 BSC 8253 timer 2 did not reach terminal count or timer 2 stuck on.
2017 BSC 8251 Data set ready failed to come on.
2018 BSC 8251 Clear to send not sensed.
2019 BSC 8251 Data set ready stuck on.
2020 BSC 8251 error
2021 BSC 8251 hardware reset failed.
2022 BSC 8251 software reset failed.
2023 BSC 8251 software "error reset" failed.
2024 BSC 8251 transmit ready did not come on.
2025 BSC 8251 receive ready did not come on.
2026 BSC 8251 could not force "overrun" error status.
2027 BSC Interrupt failure - no timer interrupt.
2028 BSC Interrupt failur....transmit, replace card or planar.
2029 BSC Interrupt failure....transmit, replace card.
2030 BSC Interrupt failure....receive, replace card or planar.
2031 BSC Interrupt failure....receive, replace card.
2033 BSC Ring indicate stuck on.
2034 BSC Receive clock stuck on.
2035 BSC Transmit clock stuck on.
2036 BSC Test indicate stuck on.
2037 BSC Ring indicate stuck on.
2038 BSC Receive clock not on.
2039 BSC Transmit clock not on.
2040 BSC Test indicate not on.
2041 BSC Data set ready not on.
2042 BSC Carrier detect not on.
2043 BSC Clear to send not on.
2044 BSC Data set ready stuck on.
2045 BSC Carrier detect stuck on.
2046 BSC Clear to send stuck on.
2047 BSC Unexpected transmit interrupt.
2048 BSC Unexpected receive interrupt.
2049 BSC Transmit data did not equal receive data.
2050 BSC 8251 detected overrun error.
2051 BSC Lost data set ready during data wrap.
2052 BSC Receive timeout during data wrap.
~~~~~
TITLE: 21XX BINARY SYNCHRONOUS COMMUNICATIONS ADAPTER ERRORS......1019
2101 ALT BCC POST failed.
2110 ALT BSC 8255 port A failure.
2111 ALT BSC 8255 port B failure.
2112 ALT BSC 8255 port C failure.
2113 ALT BSC 8253 timer 1 did not reach terminal count.
2114 ALT BSC 8253 timer 1 stuck on.
2116 ALT BSC 8253 timer 2 did not reach terminal count or timer 2 stuck on.
2117 ALT BSC 8251 Data set ready failed to come on.
2118 ALT BSC 8251 Clear to send not sensed.
2119 ALT BSC 8251 Data set ready stuck on.
2120 ALT BSC 8251 error
2121 ALT BSC 8251 hardware reset failed.
2122 ALT BSC 8251 software reset failed.
2123 ALT BSC 8251 software "error reset" failed.
2124 ALT BSC 8251 transmit ready did not come on.
2125 ALT BSC 8251 receive ready did not come on.
2126 ALT BSC 8251 could not force "overrun" error status.
2127 ALT BSC Interrupt failure - no timer interrupt.
2128 ALT BSC Interrupt failur....transmit, replace card or planar.
2129 ALT BSC Interrupt failure....transmit, replace card.
2130 ALT BSC Interrupt failure....receive, replace card or planar.
2131 ALT BSC Interrupt failure....receive, replace card.
2133 ALT BSC Ring indicate stuck on.
2134 ALT BSC Receive clock stuck on.
2135 ALT BSC Transmit clock stuck on.
2136 ALT BSC Test indicate stuck on.
2137 ALT BSC Ring indicate stuck on.
2138 ALT BSC Receive clock not on.
2139 ALT BSC Transmit clock not on.
2140 ALT BSC Test indicate not on.
2141 ALT BSC Data set ready not on.
2142 ALT BSC Carrier detect not on.
2143 ALT BSC Clear to send not on.
2144 ALT BSC Data set ready stuck on.
2145 ALT BSC Carrier detect stuck on.
2146 ALT BSC Clear to send stuck on.
2147 ALT BSC Unexpected transmit interrupt.
2148 ALT BSC Unexpected receive interrupt.
2149 ALT BSC Transmit data did not equal receive data.
2150 ALT BSC 8251 detected overrun error.
2151 ALT BSC Lost data set ready during data wrap.
2152 ALT BSC Receive timeout during data wrap.
~~~~~
TITLE: 22XX CLUSTER ADAPTER ERRORS................................1020
2201 CLUSTER ADAPTER Cluster Adapter Failure
2221 CLUSTER ADAPTER Replace Cluster Adapter
~~~~~
TITLE: 23XX PLASMA MONITOR ADAPTER ERRORS.........................1021
~~~~~
TITLE: 24XX ENHANCED GRAPHICS ADAPTER ERRORS......................1022
2401 ENHANCED GRAPHICS ADAPTER Enhanced Grahpics Adapter Failure
~~~~~
TITLE: 26XX PC/370 ERRORS.........................................1023
~~~~~
TITLE: 27XX PC/3277 ERRORS........................................1024
~~~~~
TITLE: 28XX 3278/79 EMULATION ADAPTER ERRORS......................1025
2801 3278/79 (DFCA 3270) Adapter failure (coax not attached to controller)
If 3270PC, check Keyboard/Timer adapter ROM (ECA040)
2854 3278/79 (DFCA 3270) Diagnostic Incompatibility
2859 3278/79 (DFCA 3270) Possible bad BSC Card
~~~~~
TITLE: 29XX COLOR PRINTER ERRORS..................................1026
2901 COLOR PRINTER Color Graphics printer tests failed
~~~~~
TITLE: 30XX LAN NETWORK ERRORS....................................1027
3001 LAN NETWORK Adapter Failure Replace Primary Lan Adapter
3002 LAN NETWORK ROM Failure....Replace Primary LAN Adapter
3003 LAN NETWORK I. D. Failure....Replace Primary LAN Adapter
3004 LAN NETWORK RAM Failure....Replace Primary LAN Adapter
3005 LAN NETWORK Host Interrupt Failure....Replace Primary LAN Adapter
3006 LAN NETWORK + or NEG 12V DC Failure....Replace Primary LAN Adapter
3007 LAN NETWORK Digital Wrap Failure....Replace Primary LAN Adapter
3008 LAN NETWORK Host Interrupt Failure....Replace Primary LAN Adapter
3009 LAN NETWORK Sync Failure....Replace Primary LAN Adapter
3010 LAN NETWORK Time Out Failure....Replace Primary LAN Adapter
3011 LAN NETWORK Time Out Failure....Replace Primary LAN Adapter
3012 LAN NETWORK Adapter Failure....Replace Primary LAN Adapter
3013 LAN NETWORK Digital Failure....Replace Primary LAN Adapter
3014 LAN NETWORK Digital Failure....Replace Primary LAN Network Adapter
3015 LAN NETWORK Analog Failure (RF) (adapter not hooked to translator)
3020 LAN NETWORK ROM BIOS Failure
3041 LAN NETWORK Continuous RF Signal Detected
3042 LAN NETWORK Continious RF Signal Sent....Replace Primary LAN Adapter
~~~~~
TITLE: 31XX ALTERNATE LAN NETWORK ERRORS..........................1028
3101 ALT LAN NETWORK Adapter Failure Replace Alt. Lan Adapter
3102 ALT LAN NETWORK ROM Failure....Replace Alt. LAN Adapter
3103 ALT LAN NETWORK I. D. Failure....Replace Alt. LAN Adapter
3104 ALT LAN NETWORK RAM Failure....Replace Alt. LAN Adapter
3105 ALT LAN NETWORK Host Interrupt Failure....Replace Alt. LAN Adapter
3106 ALT LAN NETWORK + or NEG 12V DC Failure....Replace Alt. LAN Adapter
3107 ALT LAN NETWORK Digital Wrap Failure....Replace Alt. LAN Adapter
3108 ALT LAN NETWORK Host Interrupt Failure....Replace Alt. LAN Adapter
3109 ALT LAN NETWORK Sync Failure....Replace Alt. LAN Adapter
3110 ALT LAN NETWORK Time Out Failure....Replace Alt. LAN Adapter
3111 ALT LAN NETWORK Time Out Failure....Replace Alt. LAN Adapter
3112 ALT LAN NETWORK Adapter Failure....Replace Alt. LAN Adapter
3113 ALT LAN NETWORK Digital Failure....Replace Alt. LAN Adapter
3114 ALT LAN NETWORK Digital Failure....Replace Alt. LAN Network Adapter
3115 ALT LAN NETWORK Analog Failure (RF) (adapter not hooked to translator)
3120 ALT LAN NETWORK ROM BIOS Failure
3141 ALT LAN NETWORK Continuous RF Signal Detected
3142 ALT LAN NETWORK Continious RF Signal Sent....Replace Alt. LAN Adapter
~~~~~
TITLE: 32XX 3270 PC DISPLAY ADAPTER ERRORS.......................1029
3201 3270 DISPLAY ADAPTER Error
3202 3270 DISPLAY ADAPTER Error
3203 3270 DISPLAY ADAPTER Error
3204 3270 DISPLAY ADAPTER Error
3205 3270 DISPLAY ADAPTER Error
3206 3270 DISPLAY ADAPTER Error
3207 3270 DISPLAY ADAPTER Error
3208 3270 DISPLAY ADAPTER Error
3209 3270 DISPLAY ADAPTER Error
3210 3270 DISPLAY ADAPTER Error
3211 3270 DISPLAY ADAPTER Error
3212 3270 DISPLAY ADAPTER Error
3213 3270 DISPLAY ADAPTER Error
3214 3270 DISPLAY ADAPTER Error
3215 3270 DISPLAY ADAPTER Error
3216 3270 DISPLAY ADAPTER Error
3217 3270 DISPLAY ADAPTER Error
3218 3270 DISPLAY ADAPTER Error
3219 3270 DISPLAY ADAPTER Error
3220 3270 DISPLAY ADAPTER Error
3221 3270 DISPLAY ADAPTER Error
3222 3270 DISPLAY ADAPTER Error
3223 3270 DISPLAY ADAPTER Error
3224 3270 DISPLAY ADAPTER Error
3225 3270 DISPLAY ADAPTER Error
3226 3270 DISPLAY ADAPTER Error
3227 3270 DISPLAY ADAPTER Error
3228 3270 DISPLAY ADAPTER Error
3229 3270 DISPLAY ADAPTER Error
3230 3270 DISPLAY ADAPTER Error
3231 3270 DISPLAY ADAPTER Error
3232 3270 DISPLAY ADAPTER Error
3233 3270 DISPLAY ADAPTER Error
3234 3270 DISPLAY ADAPTER Error
3235 3270 DISPLAY ADAPTER Error
3236 3270 DISPLAY ADAPTER Error
3237 3270 DISPLAY ADAPTER Error
3238 3270 DISPLAY ADAPTER Error
3239 3270 DISPLAY ADAPTER Error
3240 3270 DISPLAY ADAPTER Error
3241 3270 DISPLAY ADAPTER Error
3242 3270 DISPLAY ADAPTER Error
3243 3270 DISPLAY ADAPTER Error
3244 3270 DISPLAY ADAPTER Error
3245 3270 DISPLAY ADAPTER Error
3246 3270 DISPLAY ADAPTER Error
3247 3270 DISPLAY ADAPTER Error
3248 3270 DISPLAY ADAPTER Error
3249 3270 DISPLAY ADAPTER Error
3250 3270 DISPLAY ADAPTER Error
3251 3270 DISPLAY ADAPTER Error
3252 3270 DISPLAY ADAPTER Error
3253 3270 DISPLAY ADAPTER Error
3254 3270 DISPLAY ADAPTER Error
3255 3270 DISPLAY ADAPTER Error
3256 3270 DISPLAY ADAPTER Error
3257 3270 DISPLAY ADAPTER Error
3258 3270 DISPLAY ADAPTER Error
3259 3270 DISPLAY ADAPTER Error
3261 PROGAMMED SYMBOLS ADAPTER Error
3262 PROGAMMED SYMBOLS ADAPTER Error
3263 PROGAMMED SYMBOLS ADAPTER Error
3264 PROGAMMED SYMBOLS ADAPTER Error
3265 PROGAMMED SYMBOLS ADAPTER Error
3266 PROGAMMED SYMBOLS ADAPTER Error
3267 PROGAMMED SYMBOLS ADAPTER Error
3268 PROGAMMED SYMBOLS ADAPTER Error
3269 PROGAMMED SYMBOLS ADAPTER Error
3270 PROGAMMED SYMBOLS ADAPTER Error
3271 PROGAMMED SYMBOLS ADAPTER Error
3272 PROGAMMED SYMBOLS ADAPTER Error
3273 PROGAMMED SYMBOLS ADAPTER Error
3274 PROGAMMED SYMBOLS ADAPTER Error
3275 PROGAMMED SYMBOLS ADAPTER Error
3276 PROGAMMED SYMBOLS ADAPTER Error
3277 PROGAMMED SYMBOLS ADAPTER Error
3278 PROGAMMED SYMBOLS ADAPTER Error
3279 PROGAMMED SYMBOLS ADAPTER Error
3280 APA ADAPTER Error
3281 APA ADAPTER Error
3282 APA ADAPTER Error
3283 APA ADAPTER Error
3284 APA ADAPTER Error
3285 APA ADAPTER Error
3286 APA ADAPTER Error
3287 APA ADAPTER Error
3288 APA ADAPTER Error
3289 APA ADAPTER Error
~~~~~
TITLE: 35XX ENHANCED DISPLAY STATION ADAPTER ERRORS...............1030
3504 EDSEA Adapter connected to twinax during off line tests
3508 EDSEA Workstation address conflict, Incorrect Diags or Adapter
3588 EDSEA Feature not installed or Device addr. switches set
3588 EDSEA incorrectly or Adapter error.
~~~~~
TITLE: 36XX GENERAL PURPOSE INTERFACE BUS ADAPTER ERRORS..........1031
3601 GPIB ADAPTER Base Address incorrect
3602 GPIB ADAPTER Write to SPMR failed
3603 GPIB ADAPTER Write to ADR failed or addressing problems
3610 GPIB ADAPTER Adapter cannot be programmed to listen
3611 GPIB ADAPTER Adapter cannot be programmed to talk
3612 GPIB ADAPTER Adapter cannot take control with IFC
3613 GPIB ADAPTER Adapter cannot go to standby
3614 GPIB ADAPTER Adapter cannot take control asynchronously
3615 GPIB ADAPTER Adapter cannot take control synchronously
3616 GPIB ADAPTER Adapter cannot pass control
3617 GPIB ADAPTER Adapter cannot be addressed to listen
3618 GPIB ADAPTER Adapter cannot be unaddressed to listen
3619 GPIB ADAPTER Adapter cannot be addressed to talk
3620 GPIB ADAPTER Adapter cannot be unaddressed to talk
3621 GPIB ADAPTER Adapter unaddressable to listen with extended addressing
3622 GPIB ADAPTER Adapter unaddressable to listen with extended addressing
3623 GPIB ADAPTER Adapter unaddressable to listen with extended addressing
3624 GPIB ADAPTER Adapter unaddressable to listen with extended addressing
3625 GPIB ADAPTER Adapter cannot write to self
3626 GPIB ADAPTER Adapter cannot generate handshake error
3627 GPIB ADAPTER Adapter cannot detect DCL message
3628 GPIB ADAPTER Adapter cannot detect SDC message
3629 GPIB ADAPTER Adapter cannot detect END with EOI
3630 GPIB ADAPTER Adapter cannot detect EOI with EOI
3631 GPIB ADAPTER Adapter cannot detect END with 8 bit EOS
3632 GPIB ADAPTER Adapter cannot detect END with 7 bit EOS
3633 GPIB ADAPTER Adapter cannot detect GET
3634 GPIB ADAPTER Mode 3 addressing not functioning
3635 GPIB ADAPTER Adapter cannot recognize undefined command
3636 GPIB ADAPTER Adapter cannot detect REM, REMC, LOK or LOKC
3637 GPIB ADAPTER Adapter cannot clear REM or LOK
3638 GPIB ADAPTER Adapter cannot detect SRQ
3639 GPIB ADAPTER Adapter cannot conduct serial poll
3640 GPIB ADAPTER Adapter cannot conduct parallel poll
3650 GPIB ADAPTER Adapter cannot DMA to 7210
3651 GPIB ADAPTER Data error on DMA to 7210
3652 GPIB ADAPTER Adapter cannot DMA form 7210
3653 GPIB ADAPTER Data error on DMA from 7210
3658 GPIB ADAPTER Unenvoked interrupt received
3659 GPIB ADAPTER Adapter cannot interrupt of ADSC
3660 GPIB ADAPTER Adapter cannot interrupt on ADSC
3661 GPIB ADAPTER Adapter cannot interrupt on CO
3662 GPIB ADAPTER Adapter cannot interrupt on DO
3663 GPIB ADAPTER Adapter cannot interrupt on DI
3664 GPIB ADAPTER Adapter cannot interrupt on ERR
3665 GPIB ADAPTER Adapter cannot interrupt on DEC
3666 GPIB ADAPTER Adapter cannot interrupt on END
3667 GPIB ADAPTER Adapter cannot interrupt on DET
3668 GPIB ADAPTER Adapter cannot interrupt on APT
3669 GPIB ADAPTER Adapter cannot interrupt on CPT
3670 GPIB ADAPTER Adapter cannot interrupt on REMC
3671 GPIB ADAPTER Adapter cannot interrupt on LOKC
3672 GPIB ADAPTER Adapter cannot interrupt on SRQI
3673 GPIB ADAPTER Adapter cannot interrupt terminal count on DMA to 7210
3674 GPIB ADAPTER Adapter cannot interrupt terminal count on DMA from 7210
3675 GPIB ADAPTER Spurious DMA terminal count interrupt
3697 GPIB ADAPTER Illegal DMA configuration setting detected
3698 GPIB ADAPTER Illegal interrupt level configuration setting detected
~~~~~
TITLE: 38XX DATA AQUISTION ADAPTER ERRORS.........................1032
3801 DATA ACQUISITION Adapter test failed
3810 DATA ACQUISITION Timer read test failed
3811 DATA ACQUISITION Timer interrupt test failed
3812 DATA ACQUISITION Delay, BI14 test failed
3813 DATA ACQUISITION Rate, BI13 test failed
3814 DATA ACQUISITION BO14, ISIRQ test failed
3815 DATA ACQUISITION BOO, Countin test failed
3816 DATA ACQUISITION Countout, BISTB test failed
3817 DATA ACQUISITION BOO, BOCTS test failed
3818 DATA ACQUISITION BO1, BIO test failed
3819 DATA ACQUISITION BO2, BI1 test failed
3820 DATA ACQUISITION BO3, BI2 test failed
3821 DATA ACQUISITION BO4, BI3 test failed
3822 DATA ACQUISITION BO5, BI4 test failed
3823 DATA ACQUISITION BO6, BI5 test failed
3824 DATA ACQUISITION BO7, BI6 test failed
3825 DATA ACQUISITION BO8, BI7 test failed
3826 DATA ACQUISITION BO9, BI8 test failed
3827 DATA ACQUISITION BO10, BI9 test failed
3828 DATA ACQUISITION BO11, BI10 test failed
3829 DATA ACQUISITION BO12, BI11 test failed
3830 DATA ACQUISITION BO13, BI12 test failed
3831 DATA ACQUISITION BO15, AICE test failed
3832 DATA ACQUISITION BOSTB, BOGATE test failed
3833 DATA ACQUISITION BICTS, BIHOLD test failed
3834 DATA ACQUISITION AICO, BI15 test failed
3835 DATA ACQUISITION Counter interrupt test failed
3836 DATA ACQUISITION Counter read test failed
3837 DATA ACQUISITION AO0 Ranges test failed
3838 DATA ACQUISITION AO1 Ranges test failed
3839 DATA ACQUISITION AI0 Values test failed
3840 DATA ACQUISITION AI1 Values test failed
3841 DATA ACQUISITION AI2 Values test failed
3842 DATA ACQUISITION AI3 Values test failed
3843 DATA ACQUISITION Analog input interrupt test failed
3844 DATA ACQUISITION AI23 Address or Value test failed
~~~~~
TITLE: 39XX PROFESSIONAL GRAPHICS ADAPTER.........................1033
3901 PGA Adapter Tests failed
3902 PGA Rom1 self test failure
3903 PGA Rom2 self test failure
3904 PGA Ram self test failure
3905 PGA Coldstart failure cycle power
3906 PGA Data error in communications ram
3907 PGA Address error in communications ram
3918 PGA Bad data detected while read/write to 6845 'like' registers
3909 PGA Bad data detected in lower EOH bytes read/writing
3909 6845 'like' registers
3910 PGA PGC display bank output latches
3911 PGA Basic clock failure
3912 PGA Command control error
3913 PGA VSYNC scanner
3914 PGA HSYNC scanner
3915 PGA Intech failure
3916 PGA LUT address error
3917 PGA LUT red ram chip error
3918 PGA LUT green ram chip error
3919 PGA LUT blue ram chip error
3920 PGA LUT data latch error
3921 PGA Horizontal display failure
3922 PGA Vertical display failure
3923 PGA Light pen
3924 PGA Unexpected error
3925 PGA Emulator addressing error
3926 PGA Emulator data latch
3927 PGA Emulator ram base for error codes 27 - 30
3931 PGA Emulator H/V display problem
3932 PGA Emulator cursor position
3933 PGA Emulator attribute display problem
3934 PGA Emulator cursor display
3935 PGA Fundamental emulation RAM problem
3936 PGA Emulation character set problem
3937 PGA Emulation graphics display
3938 PGA Emulator character display problem
3939 PGA Emulator bank select error
3940 PGA Display ram U2
3941 PGA Display ram U4
3942 PGA Display ram U6
3943 PGA Display ram U8
3944 PGA Display ram U10
3945 PGA Display ram U1
3946 PGA Display ram U3
3947 PGA Display ram U5
3948 PGA Display ram U7
3949 PGA Display ram U9
3950 PGA Display ram U12
3951 PGA Display ram U14
3952 PGA Display ram U16
3953 PGA Display ram U18
3954 PGA Display ram U20
3955 PGA Display ram U11
3956 PGA Display ram U13
3957 PGA Display ram U15
3958 PGA Display ram U17
3959 PGA Display ram U19
3960 PGA Display ram U22
3961 PGA Display ram U24
3962 PGA Display ram U26
3963 PGA Display ram U28
3964 PGA Display ram U30
3965 PGA Display ram U21
3966 PGA Display ram U23
3967 PGA Display ram U25
3968 PGA Display ram U27
3969 PGA Display ram U29
3970 PGA Display ram U32
3971 PGA Display ram U34
3972 PGA Display ram U36
3973 PGA Display ram U38
3974 PGA Display ram U40
3975 PGA Display ram U31
3976 PGA Display ram U33
3977 PGA Display ram U35
3978 PGA Display ram U37
3979 PGA Display ram U39
3980 PGA PGC RAM timing failure
3981 PGA PGC R/W latch
3982 PGA S/R bus output latches
3983 PGA Addressing error (vertical column of memory..U2 at top)
3984 PGA Addressing error (vertical column of memory..U4 at top)
3985 PGA Addressing error (vertical column of memory..U6 at top)
3986 PGA Addressing error (vertical column of memory..U8 at top)
3987 PGA Addressing error (vertical column of memory..U10 at top)
3988 PGA Base for error codes 88 91 (hbank data latch errors)
3992 PGA RAS/CAS PGC failure
3993 PGA Multiple write modes/nibble mask errors
3994 PGA Row nibble failure (display ram)
3995 PGA PGC addressing failure
~~~~~
TITLE: 44XX 3270/G/GX DISPLAY ERRORS..............................1034
~~~~~
TITLE: 45XX IEEE-488 ADAPTER ERRORS...............................1035
~~~~~
TITLE: 56XX FINANCIAL ADAPTER ERROR...............................1036
5601 4700PC FINANCIAL SYSTEM Personal System 2 keyboard is not attached.
5601 Check connections and run test again. If test fails
5601 again have system unit serviced. (PORT 2)
5602 4700PC FINANCIAL SYSTEM Keyboard self test failed. Use a keyboard
5602 known to be good and run test again. If test fails
5602 have system unit serviced. If test runs okay have
5602 defective keyboard serviced. (PORT 2)
5603 4700PC FINANCIAL SYSTEM Invalid configuration of keyboards detected.
5604 4700PC FINANCIAL SYSTEM No port has keyboard attached to financial
5604 input conn.
5605 4700PC FINANCIAL SYSTEM Keyboard self test failed.
5606 4700PC FINANCIAL SYSTEM Selected 4700 keyboard not attached to system.
5607 4700PC FINANCIAL SYSTEM System received invalid key code from keyboard
5607 on PIN Keypad (diagnostic selection invalid).
5608 4700PC FINANCIAL SYSTEM 4700 keyboard not operating correctly
5609 4700PC FINANCIAL SYSTEM Invalid system for the keyboard program.
5610 4700PC FINANCIAL SYSTEM No PIN Keypad attached (diagnostic selection
5610 error)
5611 4700PC FINANCIAL SYSTEM Key code received other than expected
5611 by DIAG PROG. PIN keypad failed.
5612 4700PC FINANCIAL SYSTEM Encrypting PIN Keypad detected data of an
5612 incorrect length
5614 4700PC FINANCIAL SYSTEM No PIN Keypad attached to Financial Input Conn.
5615 4700PC FINANCIAL SYSTEM The key on the 4700 Kybd that is used to cancel
5615 PIN entries has an incorrect code. Pin Pad Failed Self
5615 Test.
5616 4700PC FINANCIAL SYSTEM The Pin Keypad is not attached to the pointing
5616 device connector
5617 4700PC FINANCIAL SYSTEM Pin Keypad failed self test
5618 4700PC FINANCIAL SYSTEM Pin Keypad has a communication error
5619 4700PC FINANCIAL SYSTEM System invalid for PIN keypad driver
5621 4700PC FINANCIAL SYSTEM Magnetic Stripe device error
5622 4700PC FINANCIAL SYSTEM Magnetic Stripe reader/encoder error Wrong
5622 Diagnostic Diskette Level.
5623 4700PC FINANCIAL SYSTEM No Magnetic Stripe device connected to the
5623 Financial Input Conn.
5624 4700PC FINANCIAL SYSTEM The key on the 4700 Kybd that is used to
5624 cancel PIN entries has an incorrect code.
5625 4700PC FINANCIAL SYSTEM No Magnetic Stripe device connected
5626 4700PC FINANCIAL SYSTEM Data read and data encoded by mag stripe
5626 device do not match
5627 4700PC FINANCIAL SYSTEM Magnetic stripe unit self test failed
5629 4700PC FINANCIAL SYSTEM System invalid for the magnetic stripe
5629 unit driver
5630 4700PC FINANCIAL SYSTEM STATUS = F1 system attempted unsucessful
5630 IPL from diskette.
5631 4700PC FINANCIAL SYSTEM STATUS REMOTE START attempt to establish
5631 a connection with the 4700 controller has begun.
5631 When the connection occurs 5633 appears
5632 4700PC FINANCIAL SYSTEM Diagnostics failed to load from diskette
5632 drive
5633 4700PC FINANCIAL SYSTEM STATUS REMOTE IPL. Initial loading of a
5633 program from the 4700 controller is in progress.
5634 4700PC FINANCIAL SYSTEM remote ipl error between 4700 pc and controller
5641 4700PC FINANCIAL SYSTEM Financial Input adapter failed
5651 4700PC FINANCIAL SYSTEM Financial Output adapter failed
5652 4700PC FINANCIAL SYSTEM Output failure of printer or adapter
5653 4700PC FINANCIAL SYSTEM The customization data for thr printer missing
5654 4700PC FINANCIAL SYSTEM Loop cable for the printer not connected
5655 4700PC FINANCIAL SYSTEM ERROR: PRINTER REDIRECT...error in the order
5655 of the files in the config.sys file
5661 4700PC FINANCIAL SYSTEM Financial Security adapter failed
5662 4700PC FINANCIAL SYSTEM Data Encryption tried during normal operation
5662 without the Financial Security adapter installed
5663 4700PC FINANCIAL SYSTEM No "Master Key" is present in the Financial
5663 Security adapter
5690 4700PC FINANCIAL SYSTEM 4700PC banking features not those expected.
~~~~~
TITLE: 62XX STORE LOOP ADAPTER ERRORS ............................1037
~~~~~
TITLE: 69XX SYS 36/PC DRIVER CARD ERROR CODES.....................1038
6907 SYSTEM 36/PC DRIVER CARD System/36PC expansion cable left attached
6907 to PC while running 36 Driver Card diagnostics
~~~~~
TITLE: 71XX VOICE COMMUNICATIONS ADAPTER ERRORS...................1039
~~~~~
TITLE: 73XX 3.5 INCH ADAPTER ERRORS...............................1040
~~~~~
TITLE: 74XX PERSONAL SYSTEM/2 DISPLAY ADAPTER ERRORS..............1041
~~~~~
TITLE: 76XX PERSONAL PAGE PRINTER ERRORS .........................1042
7601 PERSONAL PAGEPRINTER ADAPTER failure
7602 PERSONAL PAGEPRINTER ADAPTER failure
7603 PERSONAL PAGEPRINTER failure
7604 PERSONAL PAGEPRINTER CABLE problem
~~~~~
TITLE: 78XX HIGH SPEED ADAPTER ERRORS.............................1043
7801 HIGH SPEED ADAPTER failure
~~~~~
TITLE: 79XX 3117 SCANNER ERRORS...................................1044
7901 3117 SCANNER ADAPTER failure
7902 3117 SCANNER Lamp problem
7902 3117 SCANNER Device Card problem
7903 3117 SCANNER Device Card problem
~~~~~
TITLE: 82XX 4055 INFO WINDOW ERRORS...............................1045
8200 INFO WINDOW INVALID ERROR Contact your support structure
8200 and report this error code.
8201 INFO WINDOW NORMAL POWER ON No action necessary
8202 INFO WINDOW TIMER RESET (TIMEOUT) System controller board
8203 INFO WINDOW 8031 CHIP System controller board
8204 INFO WINDOW RAM System controller board
8205 INFO WINDOW ROM CRC 1. ROM
8205 2. System controller board
8206 INFO WINDOW RAM CRC System controller board
8207 INFO WINDOW NVRAM CRC 1. This error could be caused
8207 setting the display power switch
8207 to off during an update, or by
8207 and intermittent failure
8207 2. Data was restored from backup
8207 copy in NVRAM.
8207 3. System controller board
8208 INFO WINDOW NVRAM BATTERY 1. NVRAM battery
8208 2. System controller board
8209 INFO WINDOW NVRAM FAILURE System controller board
8210 INFO WINDOW NVRAM DATA INVALID If problem continues, replace
8210 system controller board.
8210 Possible NVRAM intermittent
8210 failure.
8211 INFO WINDOW ANALOG-TO-DIGITAL System controller board
8212 INFO WINDOW GRAPHIC SYNC FAILURE 1. Sync card
8212 2. System controller board
8213 INFO WINDOW TIME OF DAY CLOCK Set time and Date. If problem
8213 continues, replace :
8213 1. System controller board
8213 2. Sync card
8213 3. Audio card
8214 INFO WINDOW SPEECH LOGIC FAILURE 1. Audio card
8214 2. System controller board
8214 3. Power supply
8215 INFO WINDOW INTERNAL RS 232C WRAP System controller board
8216 INFO WINDOW EXTERNAL RS 232C WRAP Run test with the wrap plug on
8216 display to identify failure.
8216 System controller board
8217 INFO WINDOW HIGH RESOLUTION SYNCS If the test screen was
8217 distorted :
8217 1. IBM EGA card
8217 2. IBM EGA jumper card
8217 If the test screen was
8217 readable :
8217 1. Sync card
8217 2. System controller board
8218 INFO WINDOW LOW FREQUENCY SYNCS If the test screen was
8218 distorted :
8218 1. IBM EGA card
8218 2. IBM EGA jumper card
8218 If the test screen was
8218 readable :
8218 1. Sync card
8218 2. System controller board
8219 INFO WINDOW EGA RGB SIGNALS TEST 1. IBM EGA card
8219 2. IBM EGA jumper card
8219 3. Sync card
8219 4. System controller board
8220 INFO WINDOW RGB INSERT COMPARE Sync card
8221 INFO WINDOW MISSING HI/LOW BEEPS 1. Audio card
8221 2. System controller board
8222 INFO WINDOW RT CHANNEL AUDIO 1. Audio card
8222 2. System controller board
8223 INFO WINDOW LT CHANNEL AUDIO 1. Audio card
8223 2. System controller board
8224 INFO WINDOW NO SYNCS VIDEO #1 1. Sync card
8224 2. Decoder card
8224 3. System controller board
8225 INFO WINDOW NO SYNCS VIDEO #2 1. Sync card
8225 2. Decoder card
8225 3. System controller board
8226 INFO WINDOW 16/64 COLOR MODE 1. Switching card
8226 2. System controller board
8227 INFO WINDOW LEFT/RIGHT SHIFT 1. Deflection board
8227 2. System controller board
8227 3. Switching card
8228 INFO WINDOW AUX MONITOR ON/OFF 1. Decoder card
8228 2. System controller board
8229 INFO WINDOW INTERLACE ON/OFF 1. Sync card
8229 2. Deflection board
8230 INFO WINDOW VIDEO INPUT SELECT 1. Decoder card
8230 2. System controller board
8231 INFO WINDOW RGB ONLY MODE Sync card
8232 INFO WINDOW COMPOSITE ONLY MODE 1. Sync card
8232 2. System controller board
8232 3. Switching card
8232 4. Decoder card
8233 INFO WINDOW OVERLAY 1. Switching card
8233 2. Deflection board
8233 3. Sync card
8234 INFO WINDOW RGB/VIDEO Sync card
8235 INFO WINDOW SYSTEM TIMER TEST System controller card
8236 INFO WINDOW INTERNAL PROGRAM 1. Verify that the system
8236 diskette and ROM levels are
8236 compatible.
8236 2. System controller board
8237 INFO WINDOW CANNOT CALIBRATE 1. System controller board
8237 2. Touch screen
8237 3. Power supply
8238 INFO WINDOW CONTROL PROGRAM Contact your support structure
8238 and report this error code.
8238 Possible system controller board
8239 INFO WINDOW CONTROL PROGRAM Contact your support structure
8239 and report this error code.
8239 Possible system controller board
8240 INFO WINDOW CPU NOT LISTENING 1. IBM GPIB card
8240 2. System controller board
8241 INFO WINDOW GPIB SEND/RECV COUNT Contact your support structure
8241 and report this error code.
8242 INFO WINDOW RS-232C INTERFACE 1. Run the wrap test with the
8242 wrap plug on the display to
8242 test the display.
8242 2. System controller board
8243 INFO WINDOW TOUCH SCREEN System controller board
8244 INFO WINDOW FAILURE OF VDP-1 Locate problem in VDP-1 cable
8245 INFO WINDOW FAILURE OF VDP-2 Locate problem in VDP-2 cable
8246 INFO WINDOW A1/A2 DETECTION 1. Sync card
8246 2. System controller board
8247 INFO WINDOW HIGH RESOLUTION SYNCS Sync card
8248 INFO WINDOW TV FREQUENCY SYNCS Sync card
8249 INFO WINDOW GPIB (BUS) System controller board
8250 INFO WINDOW CRC ERRORS DETECTED 1. IEEE 488 cable
8250 2. IBM PC GPIB card
8250 3. System controller board
8251 INFO WINDOW CRC ERRORS DETECTED 1. IEEE 488 cable
8251 2. IBM PC GPIB card
8251 3. System controller board
8252 INFO WINDOW GPIB TIME OUT 1. IBM PC GPIB card
8252 2. System controller board
8252 3. IEEE 488 cable
8252 4. Power supply
8252 5. Videodisc player problem
8253 INFO WINDOW GPIB TIME OUT 1. IBM PC GPIB card
8253 2. System controller board
8253 3. IEEE 488 cable
8253 4. Power supply
8253 5. Videodisc player problem
8254 INFO WINDOW GPIB SEQUENCE ERROR Contact your support structure
8254 and report this error code.
8255 INFO WINDOW INT PROGRAM ERROR 1. Contact your support structure
8255 and report this error code.
8255 2. system controller board
8256 INFO WINDOW TIME OUT 1. System controller board
8256 2. Sync card
8256 3. IEEE 488 cable
8256 4. IBM PC GPIB card
8257 INFO WINDOW RETRIES OF CRC ERRORS 1. System controller board
8257 2. IEEE 488 cable
8257 3. IBM PC GPIB card
8258 INFO WINDOW ERROR IN GPIB COMMS 1. System controller board
8258 2. IEEE 488 cable
8258 3. IBM PC GPIB card
8259 INFO WINDOW GPIB CONTROLLER ERROR 1. IBM PC GPIB card
8259 2. IEEE 488 cable
8259 3. System controller board
8260 INFO WINDOW INSERT CONTROL LOGIC 1. Sync card
8260 2. System controller board
8261 INFO WINDOW WRONG RGB COLOR 1. Video output board
8261 2. Switching card
8261 3. Sync card
8261 4. System controller board
8261 5. CRT and yoke assembly
8262 INFO WINDOW PLAYER RESPONSE 1. Verify that videodisc
8262 is on and contains a videodisc
8262 2. Go to the IBM Infowindow
8262 Guide to Operations and test
8262 the videodisc player interface.
8263 INFO WINDOW ADDITIONAL EQUIPMENT Audio problem :
8263 Replace audio card
8263 Dual frequency monitor failure :
8263 Replace switching card
8263 Color composite monitor failure :
8263 Replace decoder card
8264 INFO WINDOW RGB OUTPUT SIGNALS Sync card
8265 INFO WINDOW EGA CLOCK ERROR 1. IBM EGA jumper card
8265 2. IBM EGA card
8266 IBM EGA JUMPER INTERRUPT ERROR 1. IBM EGA card switch settings
8266 2. IBM EGA jumper card
8266 3. IBM EGA card
8267 INFO WINDOW EGA GRAPHICS SYNC 1. IBM PC graphic sync cable
8267 2. IBM EGA jumper card
8267 3. Sync card
8267 4. IBM EGA card
8268 SYNC PRESENT WITHOUT CABLE IBM EGA card
8269 NO AUDIO VIDEODISC 1/L INPUT Audio card
8270 NO AUDIO VIDEODISC 2/R INPUT Audio card
8271 INFO WINDOW IBM EGA CARD MAP 0222 : Failure isolation
8271 for the IBM EGA card. Perform
8271 IBM EGA card failure isolation
8272 INFO WINDOW EGA MEMORY FAILURE Replace IBM EGA card
8273 INFO WINDOW EGA GRAPHICS MEMORY MAP 0225 : Failure isolation
8273 for memory modules. Perform
8273 memory module failure isolation
8274 RESERVED Contact your support structure
8274 and report this error code.
8275 RESERVED Contact your support structure
8275 and report this error code.
8276 DISKETTE CANNOT SUPPORT See IBM Infowindow
8276 DISPLAY ROM LEVEL compatibility levels
8277 RESERVED Contact your support structure
8277 and report this error code
8278 INFO WINDOW HI RES DISPLAY 1. Switching card
8278 2. Sync card
8278 3. MAP 0222 : Failure isolation
8278 for the IBM EGA card. Perform
8278 IBM EGA card failure isolation.
8279 INFO WINDOW TIME OF DAY CLOCK System controller board
8280 IBM PC DOS ERROR OCCURRED 1. Follow directions on screen
8280 2. Contact your support structure
8280 and report this error code.
~~~~~
TITLE: 84XX SPEECH ADAPTER ERRORS.................................1046
~~~~~
TITLE: 85XX EXPANDED MEMORY ADAPTER ERRORS........................1047
~~~~~
TITLE: 91XX 3363 OPTICAL DISK DRIVE ERRORS........................1048
9101 OPTICAL DISK POST ERROR - Drive #1 failed - Reseat Cables and Adapter
9102 OPTICAL DISK POST ERROR - Drive #1 failed - Reinsert Cartridge
9102 - Reseat Adapter
9103 OPTICAL DISK POST ERROR - Drive #1 failed - Reseat Cables and Adapter
9104 OPTICAL DISK POST ERROR - Drive #2 failed - Reseat Cables and Adapter
9105 OPTICAL DISK POST ERROR - Drive #2 failed - Reinsert cartridge
9105 - Reseat cables and Adapter
9106 OPTICAL DISK POST ERROR - Drive #2 failed - Reseat cables and Adapter
9107 OPTICAL DISK POST ERROR - Adapter hung on BUSY - Reseat Cables and Adapter
9110 OPTICAL DISK DIAGS ERROR - Data not recorded - Check Adapter, Drive, Cable
9111 OPTICAL DISK DIAGS ERROR - Data not readable - Check Adapter, Drive, Cable
9112 OPTICAL DISK DIAGS ERROR - Sector demarked - Check Adapter, Drive, Cable
9113 OPTICAL DISK DIAGS ERROR - Controller Error - Check Adapter, Drive, Cable
9113 - Check switch settings
9113 on Adapter DS302
9113 (8088 vs 80286)
9114 OPTICAL DISK DIAGS ERROR - Sector Read/Write Error - Check Drive, Adapter, or Cable
9115 OPTICAL DISK DIAGS ERROR - Scramble Buffer Error - Check Drive, Adapter
9115 - Check Cable
9116 OPTICAL DISK DIAGS ERROR - Data Buffer Error - Check Drive, Adapter
9116 - Check Cable
9117 OPTICAL DISK DIAGS ERROR - Drive RAM/ROM Error - Check Drive, Adapter
9117 - Check Cable
9118 OPTICAL DISK DIAGS ERROR - Invalid Command - Check Drive, Adapter, Cable
9119 OPTICAL DISK DIAGS ERROR - Track Jump Error - Check Drive, Adapter, Cable
9120 OPTICAL DISK DIAGS ERROR - Laser Error - Check Drive, Adapter, or Cable
9121 OPTICAL DISK DIAGS ERROR - Focus Error - Check Cartridge, Drive, Adapter, or Cable
9122 OPTICAL DISK DIAGS ERROR - Motor Sync Error - Cartridge upside down
9122 - Check Drive, Adapter, Cable
9123 OPTICAL DISK DIAGS ERROR - Write Fault - Check Drive, Adapter, or Cable
9124 OPTICAL DISK DIAGS ERROR - General Drive Error - Check Drive, Adapter
9124 - Check Cable
9125 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter
9125 - Check Cable
9126 OPTICAL DISK DIAGS ERROR - Invalid Command - Check Drive, Adapter, Cable
9127 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter
9127 - Check Cable
9128 OPTICAL DISK DIAGS ERROR - Disk Not Initialized - Check Drive, Adapter
9128 - Check Cable
9129 OPTICAL DISK DIAGS ERROR - Disk ID Did Not Match - Check Drive, Adapter
9129 - Check Cable
9130 OPTICAL DISK DIAGS ERROR - Read-Only Disk Installed - Check Disk
9130 - Check Drive, Adapter
9130 - Check Cable
9131 OPTICAL DISK DIAGS ERROR - No Disk Present - Check Disk
9131 - Check Drive, Adapter, Cable
9132 OPTICAL DISK DIAGS ERROR - Illegal Disk Detected - Check Disk
9132 - Check Adapter, Drive
9132 - Check Cable
9133 OPTICAL DISK DIAGS ERROR - No Disk Change Detected - Check Drive, Adapter
9133 - Check Cable
9134 OPTICAL DISK DIAGS ERROR - Read-Only Disk Detected - Check Drive, Adapter
9134 - Check Cable
9135 OPTICAL DISK DIAGS ERROR - Illegal Disk Detected - Check Drive, Adapter
9135 - Check Cable
9136 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Adapter, Drive
9136 - Check Cable
9138 OPTICAL DISK DIAGS ERROR - No Disk Change Detected - Retry test again
9138 - Check Drive, Adapter
9138 - Check Cable
9141 OPTICAL DISK DIAGS ERROR - No Disk Change Detected - Retry tests
9141 - Check Drive, Adapter
9141 - Check Cable
9144 OPTICAL DISK DIAGS ERROR - WRITE-PROTECT Window Not Opened - Retry tests
9144 - Check Drive
9144 - Check Adapter
9144 - Check Cable
9145 OPTICAL DISK DIAGS ERROR - No Disk Change Detected - Retry tests
9145 - Check Drive, Adapter
9145 - Check Cable
9146 OPTICAL DISK DIAGS ERROR - WRITE-PROTECT Window Not Closed - Retry tests
9146 - Check Drive
9146 - Check Adapter
9146 - Check Cable
9148 OPTICAL DISK DIAGS ERROR - Adapter Card - Check Adapter, Drive, or Cable
9150 OPTICAL DISK DIAGS ERROR - Seek Command Failed - Check Drive, Adapter
9150 - Check Cable
9151 OPTICAL DISK DIAGS ERROR - Not At Track Zero - Check Drive, Adapter
9151 - Check Cable
9152 OPTICAL DISK DIAGS ERROR - Track Address Error - Check Drive, Adapter
9152 - Check Cable
9153 OPTICAL DISK DIAGS ERROR - Not At Track 17099 - Check Drive, Adapter
9153 - Check Cable
9154 OPTICAL DISK DIAGS ERROR - Track Address Error - Check Drive, Adapter
9154 - Check Cable
9155 OPTICAL DISK DIAGS ERROR - Track Address 17K Not Found - Check Drive
9155 - Check Adapter
9155 - Check Cable
9156 OPTICAL DISK DIAGS ERROR - Seek Time Too Long - Check Drive, Adapter
9156 - Check Cable
9157 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter
9157 - Check Cable
9158 OPTICAL DISK DIAGS ERROR - No Data Read Error Found - Check Drive, Adapter
9158 - Check Cable
9159 OPTICAL DISK DIAGS ERROR - No Null Sector Found - Check Drive, Adapter
9159 - Check Cable
9160 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter
9160 - Check Cable
9161 OPTICAL DISK DIAGS ERROR - Write Command Failed - Check Drive, Adapter
9161 - Check Cable
9162 OPTICAL DISK DIAGS ERROR - Data Compare Error - Check Drive, Adapter
9162 - Check Cable
9163 OPTICAL DISK DIAGS ERROR - Read Verify Error - Check Drive, Adapter
9163 - Check Cable
9164 OPTICAL DISK DIAGS ERROR - Demark Verify Failed - Check Drive, Adapter
9164 - Check Cable
9165 OPTICAL DISK DIAGS ERROR - Demark Bit Not Set - Check Drive, Adapter
9165 - Check Cable
9166 OPTICAL DISK DIAGS ERROR - Seek 1/3 Timing Error - Check Drive, Adapter
9166 - Check Cable
9167 OPTICAL DISK DIAGS ERROR - Seek 2/3 Timing Error - Check Drive, Adapter
9167 - Check Cable
9168 OPTICAL DISK DIAGS ERROR - Seek 3/3 Timing Error - Check Drive, Adapter
9168 - Check Cable
9170 OPTICAL DISK DIAGS ERROR - Seek Error Set - Check Drive, Adapter, Cable
9171 OPTICAL DISK DIAGS ERROR - Controller RAM/ROM Error - Check Drive, Adapter
9171 - Check Cable
9172 OPTICAL DISK DIAGS ERROR - Demark Function Error - Check Drive, Adapter
9172 - Check Cable
9173 OPTICAL DISK DIAGS ERROR - Detected Error Set - Check Drive, Adapter
9173 - Check Cable
9174 OPTICAL DISK DIAGS ERROR - Modulator/Demodulator Error - Check Drive
9174 - Check Adapter
9174 - Check Cable
9175 OPTICAL DISK DIAGS ERROR - Invalid Command - Check Adapter, Drive, Cable
9176 OPTICAL DISK DIAGS ERROR - Illegal Disk Error - Check Adapter, Drive, Cable
9177 OPTICAL DISK DIAGS ERROR - Both drives set to same address or wrong address
9178 OPTICAL DISK DIAGS ERROR - ID Mismatch - Check Drive, Adapter, or Cable
9179 OPTICAL DISK DIAGS ERROR - Sector Not Found - Check Drive, Adapter, Cable
9181 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter
9181 - Check Cable
9182 OPTICAL DISK DIAGS ERROR - Read Command Error - Check Drive, Adapter, Cable
9185 OPTICAL DISK DIAGS ERROR - Diagnostic Track Error - Check Drive, Adapter
9185 - Check Cable
9186 OPTICAL DISK DIAGS ERROR - Diagnostic Demark Error - Check Drive, Adapter
9186 - Check Cable
9187 OPTICAL DISK DIAGS ERROR - No Demark Bit Set - Check Drive, Adapter, Cable
9198 OPTICAL DISK DIAGS ERROR - Invalid Command - Re-IPL CPU with ON/OFF switch
~~~~~
TITLE: PARITY ERRORS..............................................1049
Parity Check 1 Error....Memory on System Board
Parity Check 2 Error....Memory on Memory Expansion Card
~~~~~
TITLE: ROM ERRORS.................................................1050
F0000-ROM ERROR....Replace System Board
F1000-ROM ERROR....Replace System Board
F2000-ROM ERROR....Replace System Board
F3000-ROM ERROR....Replace System Board
F4000-ROM ERROR....Replace System Board
F5000-ROM ERROR....Replace System Board
F6000-ROM ERROR....Replace System Board
F7000-ROM ERROR....Replace System Board
F8000-ROM ERROR....Replace System Board
F9000-ROM ERROR....Replace System Board
FA000-ROM ERROR....Replace System Board
FB000-ROM ERROR....Replace System Board
FC000-ROM ERROR....Replace System Board
FD000-ROM ERROR....Replace System Board
FE000-ROM ERROR....Replace System Board
C0000-ROM ERROR....Replace keyboard timer card
CA000-ROM ERROR....Replace Keyboard timer card
C8000-ROM ERROR....Replace Fixed Disk Adapter
C8000-ROM ERROR....Replace System Board
CC000-ROM ERROR....Replace System Board
D0000-ROM ERROR....Replace Cluster Adapter
D8000-ROM ERROR....Replace Store Loop Adapter
~~~~~